{"product_id":"west-coast-clutch-cover-261-362-400","title":"WEST COAST CLUTCH COVER 261\/362\/400","description":"\u003cdiv class=\"nav nav-tabs\"\u003e\n\u003cdiv class=\"prod-tab active\" data-id=\"tab1\"\u003eDescription\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"tab1 tab-content active\"\u003e\n\u003cp data-pm-slice=\"1 1 []\"\u003eOur cover provides\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003esuperior strength, durability, and functionality\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eover the stock cover. \u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan\u003eM\u003c\/span\u003e\u003cspan\u003eade of 6061-T6 Aircraft Aluminum\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eStronger than factory cover\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eLarger for better chip management\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eExtra large and longer lasting polyurethane chip deflector \u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eWider for ease of walking chain back on without removing cover \u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eField tested to ensure quality\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eBigger in size than the stock cover makes it slightly heavier \u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eIncludes bar nuts, chain sliders and one chip deflector\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eMade in the USA\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eREAD BELOW FOR IMPORTANT FIT NOTES\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe recommended torque range for the bar nuts is 20-25 ft-lbs. This will ensure that the bar is clamped properly. If not done correctly, this can cause damage to your cover.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003c\/span\u003e\u003cstrong\u003eClutch Covers cannot be retrofitted from standard bar nuts to captive, and vice versa. They are uniquely manufactured.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAll Clutch Covers fit the 3, 4 \u0026amp; 5 point felling dogs with the follow exception.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003ePart 100-1003 (when used on an 046\/460\/036\/034) - Only fits 3-point dogs\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePart 100-1004 (261\/msa300\/362\/400) - Only fits 3-point dogs\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eOur 261\/msa300\/362\/400 Clutch Cover fits the full wrap 362 (R model) with Stihl part number 1140 021 1105. \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOlder 261 models may need Stihl part number 1141 021 1130 to fit.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIf you plan to run a 404 chain, you may need to shave 0.015 (inch) off the chain slider to allow for the additional width.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eINSTALLATION TIP\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eFelling dog bolts need to be installed from the inside of the cover, facing out so that the nut is on the outside of the felling dog. After this, p\u003c\/span\u003eut the cover flat on a table and make sure that you pound the chain sliders down until it stops against the cover - as far as it will go. The clearances are super tight so we get maximum wear out of our chain sliders. Once they are down tight your chain will spin freely. \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cb\u003e\u003cspan\u003eⒹ\u003c\/span\u003e\u003c\/b\u003e\u003cb\u003e\u003cspan\u003e CANADA DESIGN REG. NO. 210518, WESTCOAST SAW, LLC\u003c\/span\u003e\u003c\/b\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Arboristudstyr","offers":[{"title":"Default Title","offer_id":54599155253571,"sku":"WC-100-1004","price":1300.0,"currency_code":"DKK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0601\/7204\/2428\/files\/Clutch_Cover_261_362_400.webp?v=1782897950","url":"https:\/\/arboristudstyr.dk\/products\/west-coast-clutch-cover-261-362-400","provider":"Arboristudstyr","version":"1.0","type":"link"}